行业动态

当前位置:网站首页 >> 新闻资讯 >> 行业动态 >> 查看详情

行业动态

冷干机除水流程简介

来源:杭州优联超滤设备有限公司  日期:2017-04-10 15:40:02  点击:2469  属于:行业动态
压缩空气先进入前置后部冷却器(B),把高温的压缩空气温度降低后,再进入高效率错流的交换器(C),此时压缩空气在热交换器内极速冷冻,精制到2~8℃,然后进一步进入高效率的三级气水分离器(D),低温的空气在三级气水分离器内一级极速旋转分离
压缩空气先进入前置后部冷却器(B),把高温的压缩空气温度降低后,再进入高效率错流的交换器(C),此时压缩空气在热交换器内极速冷冻,精制到2~8℃,然后进一步进入高效率的三级气水分离器(D),低温的空气在三级气水分离器内一级极速旋转分离,再进入二级超级重心分离段,然后再进入精细隔板分离段进行精细分离水份后,被分离出来的水份利用全自动排水装置(E)将水份排出系统外,最后得到干燥的压缩空气。这得益于其先进的技术。
Compressed air first enters the front rear cooler (B), the temperature of the compressed air temperature is reduced, then enters the efficient cross flow switch (C), the speed of the compressed air in the heat exchanger freezing, refined to 2 to 8 DEG C, three gas water separator and then further into the high efficiency, low temperature (D) the air in the three stage gas water separator a rotating speed of separation, and then enter the two stage super gravity separation section, and then enter the fine partition section of water after the separation of fine separation, separated by automatic water drainage device (E) water will be discharged from the system, and finally get the dry compressed air. Thanks to its advanced technology.
压缩空气经过冷冻、分离后,干燥的压缩空气再进入回温器(G),利用空气的冷量提升散热效果,更可以让干燥后的出口空气温度进一步回升到15~40℃,以防止出口空气管道出现结露、滴水、生锈等二次问题。
The compressed air after freezing, separation, dry compressed air enters the heater (G), enhance the cooling effect by cold air, more can make the outlet air temperature after drying further rose to 15 to 40 DEG C, to prevent condensation, water, rust and other two problems of outlet air pipe.

制冷系统其他附件有:干燥过滤器、视镜、热气旁通阀、储液器、风机压力开关机水量调节阀、高低压保护开关、排水装置等。
 
1、干燥过滤器:过滤制冷剂系统中的水分和颗粒杂质,清楚酸性物质形成的危险。
 
2、视镜:
a、流动状况以及系统的状态;
b、观察制冷系统有无存在水。
 
3、水量调节阀水冷式(ND-W或WW机型)冷干机配置:控制制冷系统中的冷媒高压,起到稳定自动调整高压,使高压压力得到保证。
 
4、热气旁通阀:控制制冷系统中的冷媒低压即蒸发温度,防止蒸发器中结冰出现冰堵得现象。
 
5、储液器:收集并储存液态冷媒,保证只有气态冷媒进入压缩机,防止液击的现象发生。
 
6、高低压保护开关:进行压缩机自身保护的功能,防止压缩机电机烧毁。当压缩机排出压力超过设定值或吸入压力低于设定值时,压力保护开关自动切断电路,使压缩机得到安全保护的作用,一般设定值为:
 
高压设定值:2.5MPa               低压设定值:0.2MPa
 
7、风机压力开关:控制风机的启动和停止,一般高压压力在1.9MPa时风机自动启动,压力下降到1.3~1.5 MPa左右时停止。与高低压压力开关的区别是风机压力开关无复位装置。